Sunday, October 20, 2013

How to Make a Simple Halloween Deco Mesh Wreath--DIY

Previously I had a nice, normal BORING fall wreath on my door.  But since Halloween was right around the corner I decided to step out of my comfort zone and try to create my own FUN deco mesh wreath.  I'm happy to report that one week later the wreath is still in tact and has received lots of compliments from friends and neighbors.  :)



Here are the supplies I used:
  • One 30 inch wire wreath frame
  • One 10 inch roll of black deco mesh
  • One 10 inch roll of purple deco mesh
  • One roll of green and white polka dot ribbon
  • One set of battery-operated LED lights
  •  One wooden Halloween decoration
  • Hot glue
  • Floral wire
  • Floral wire cutter
All together, everything cost me about $30 (all 40-50% off at Hobby Lobby).  (I already had a glue gun, floral wire, and wire cutter.)  Great bargain!

Step 1:   Since I wasn't using a "work wreath" (which would have been lots easier) I had to first attach wire at points along the wreath frame.  This is the boring part.  So that the wires wouldn't slide around, I inserted them diagonally so that they wrapped around each side of the vertical divider on the wreath frame.  Make sure to cut your wires extra long; you'll use these to wire in ALL of the deco mesh, ribbon, and lights.


I actually ended up putting in two sets of wires.  One set that stuck outside of the wreath frame (as pictured above)...

And one set that pointed toward the inside of the wreath (as pictured above here).  (I was impatient and put on my black deco mesh before attaching the second set of wires.)  :)

Step 2:  After all the wires are on, you are ready to start attaching the mesh! To start with, you'll take a piece and pinch it up a few inches from the end.  Place it inside the wires on the OUTSIDE of the frame and twist to secure. 


Now just keep unrolling the deco mesh, take a piece about 12 inches long and pinch and secure again.  Go all the way around the wreath.


I ended up doing two rows of the black since I wanted it to be thick and fluffy.  The first row angled out AWAY from the wreath frame as you can see above.  The second row angled toward the INSIDE of the frame (as you can see below). You're going to work your way from the outside of the wreath to the inside.





Step 3:  Add the second color of deco mesh.  You want this to be on the very inside of the wreath, so you'll be using the second set of wires you attached. Go all the way around, and when you get to where you started leave a tail and cut off.  Tuck the tail into the wreath so no one sees it.


Step 4:  Now you are ready to add the ribbon.  You can do this one of two ways.  I picked a starting point and wired it in every TWO wires leaving the ribbon with lots of slack so it would be fluffy.  OR, you could actually wrap the full wreath with the ribbon so that it moves diagonally across both the black and purple mesh.  If you do this, you may need more ribbon.

Once you've gone all the way around, just cut and tuck.


Step 5:  Make a bow by taking a separate piece of ribbon.  I did this by figuring out how long I wanted the tail, then pinching and making a loop, pinching and making a second loop, and pinching and making a third loop.  Hold it all together and cut, leaving length for a second tail.  I gathered it all together and wired it in toward the left side of the bottom of the wreath.  (You could put this anywhere, but I decided on the bow being off-center just to make it more interesting.)


Step 6:  Lights!  I just wired these in every second wire the same way I did for the ribbon.  The battery pack hangs down behind the big bow, so based on that I made my starting point strategic.



Step 7:  The final step will be adding your wooden decorations.  (I took the picture of the bow above once I had finished with the entire wreath, but I really did add the wooden decoration as the last step.)  I first tried to glue in my decoration, but it was so large and heavy that it wasn't holding.  There were little curly wires coming out of the pumpkins, so I actually took a piece of floral wire, wrapped it around each pumpkin wire, and then wired it into the wreath.  That way I knew it wasn't going anywhere!  For the final step, I did end up using hot glue just to flatten it into the wreath.


Step 8:  Hang it up!  Once you get it hung up you'll see some things that bother you, but it is pretty easy to make adjustments and tweak the placement of different mesh loops, ribbon, etc.


Overall, this was very fun and easy to make, and quite a bargain given that a wreath this size with lights would cost over $100.  (Lots of cute ones on Etsy!)

Obviously this one is very simple, and the sky is the limit with the types of adornments you can add.  And seriously, the work wreaths with pre-attached wires/pipe cleaners are totally the way to go.

Give it a try and let me know how it turns out.  I LOVE looking at different wreaths, so send me pictures of your different ones for Halloween, Thanksgiving, football, etc.

HAVE FUN!


Saturday, October 19, 2013

Fall Decor Home Tour 2013!

Hello Friends,

Fall has arrived...in Texas!  This time of year is probably my favorite for a variety of reasons. 


1)  The air is crisp and cool less humid, and there is a hint of spice and burning wood lingering everywhere.  (I'm counting the days until the first outside fire...and hot cocoa...and s'mores.)

2)  Burning candles add instant coziness to the house.

3)  Scarves make everything cuter.

4)  And adorable kids get to sit on bales of hay with scarecrows.  :)



Of course, my FAVORITE thing to do is DECORATE.  (Ok, seriously, I actually put out the fall decorations during Labor Day weekend, but you know...)

I thought I'd post a few pictures of the decor in my house and also link to the video of my house tour.
WARNING:  The video is the FIRST one I've ever made, so the quality is BAD.  I had no idea what I was doing.

That said, if you really like some of the things I've done, the video will give you more explanation on where I purchased things or why I arranged things a certain way.

FALL HOME TOUR VIDEO:  http://www.youtube.com/watch?v=fQRsc05-uN8

Enjoy, and happy decorating!  (And please, enjoy a mug of apple cider on your back porch for me.)

~Christy


Simple fall mantle with burlap leaves garlands (Hobby Lobby, approximately $15 per garland--two garlands pictured here)






Gotta love simple pumpkin displays.  (Stool purchased at Ross several years ago, less than $10)
Pottery Barn pillow cover.  Total steal on a "flash" website sale.  $14.99 per cover plus free S&H!  (Used a 20 inch pillow insert from the sofa throw pillows and stored the extra sofa pillow cover.)
Entry table subtly decorated for fall.
Hobby Lobby frames plus pieced together items to create the feather candle display.  Check out my video for the details.
Dining room table.  Almost all decor from TJ Max.
Halloween wreath!  It even has twinkling purple lights.  Total cost was $30 for all supplies.  TUTORIAL COMING UP ON HOW TO MAKE THIS!